Shower screensCare and safety

Replacing an old shower screen: signs, options and what to expect

DB Glass 5 min read

Silver semi-frameless corner shower screen beside a freestanding bath in a white bathroom, installed in Golden Beach
Semi-frameless, ChromeA corner screen with a pivot door beside a freestanding bath

An old shower screen rarely fails all at once. The glass clouds over, the frame pits and stains, the door starts to drop or leak, and cleaning stops making a difference. Replacing the screen is one of the simplest ways to refresh a bathroom without a full renovation, because in most cases the tiles, hob and tapware stay where they are.

Signs it is time to replace your screen

  • Cloudy edges or dark marks inside the glass. This is delamination, where moisture has worked into the layers of older laminated glass. The damage is inside the glass, so it cannot be cleaned off. Read more about shower glass delamination.
  • Glass that stays dull after a proper clean. Years of hard water and soap scum can etch the surface, leaving a haze that ordinary cleaning will not remove.
  • Corroded, pitted or stained frames. Once aluminium starts to pit, it holds grime and is very hard to bring back.
  • A door that drops, sticks or will not close properly. Worn pivots, hinges or rollers make the door harder to use and let water escape.
  • Water on the bathroom floor. Worn seals and failed silicone let water out of the shower. Our guide to shower screen leaks helps you work out where it is coming from.
  • A dated look. Heavy frames and older finishes can date a bathroom that is otherwise in good condition.

What usually stays

Replacing a screen does not normally mean replacing the bathroom. The new screen is measured to fit the existing walls, floor and hob, so the tiles and tapware stay in place. Walls are rarely perfectly square and shower floors are laid with falls towards the waste, so every new screen is measured on site and made to suit the space as it is.

Older frames are screwed and siliconed to the tiles, so taking one out can leave fixing holes or silicone marks. A photo of the existing screen shows how it is fixed, so we can plan the new layout around them.

One thing a new screen cannot fix is water damage behind the tiles. If you have noticed swollen skirting, lifting tiles or damp on the other side of the wall, have the waterproofing checked by a licensed waterproofer, or a plumber if a tap or pipe is suspected, before the new screen goes in.

Your options for a new screen

Replacement is a chance to change the style, not just swap like for like.

Semi-frameless. 6 mm toughened glass with an aluminium frame around the perimeter only, a pivot door or a sliding door, and eight frame colours for the pivot door or five for the slider. Semi-frameless screens suit corner, diamond, nib wall, over bath and alcove layouts, which covers most older showers, and they offer better water retention options than frameless. See semi-frameless shower screens.

Frameless. 10 mm toughened glass held by hinges, clamps or channels, with no frame around the glass, for the most open look. Frameless panels are heavier, and depending on the layout they may need proper wall and header support, which we check when we measure. See frameless shower screens.

Sliding. If the old door has always clashed with the vanity or toilet, a semi-frameless slider or a frameless barn door slider moves across the opening instead of swinging into the room. Our guide to sliding or hinged shower screens compares the two.

The glass is worth a second look too. Low iron glass has almost none of the green edge of standard clear glass, which shows most against white tiles, and acid etched or narrow reed glass adds privacy while still letting light through. See choosing the right glass.

How replacement works

A replacement follows the same steps as any new screen, with two additions. When you ask for a price, mention that the old screen needs to come out and include a close photo of how it is fixed. On the day, the old screen is taken out before the new one is fitted, sealed and checked to Australian Standards, with the room left clean.

Every new screen is measured on site and made to size, so the glass fits the walls and floor exactly. Our guide to getting a shower screen quote explains what to measure and photograph, and what happens after you send it.

Get a price for a replacement screen

Get a quote with rough sizes and a few photos of your current screen, and include your suburb. For help with budgeting, read what affects the cost of a shower screen, and see what to send for an accurate quote. Our shower screen replacement page sets out how the job works from start to finish.

Shower screen replacement questions

Do I need to retile to replace a shower screen?

Not normally. A new screen is measured to fit the existing walls, floor and hob, so the tiles and tapware can stay. If water has been getting behind the tiles, the waterproofing should be repaired before the new screen is fitted.

Can you remove my old shower screen?

Yes. Removing your existing screen can be included in the job. Mention it when you ask for a price and include a photo of the current screen.

Can I change from a framed screen to frameless?

In many bathrooms, yes. Frameless panels use heavier 10 mm glass and, depending on the layout, may need proper wall and header support, so we confirm the layout when we measure on site.

Why is my shower glass still cloudy after cleaning?

Either the surface has been etched by years of hard water and soap scum, or moisture has got inside older laminated glass and caused delamination. Neither comes off with ordinary cleaning, and replacing the glass is the lasting fix.

Replace your old shower screen

Send rough sizes and a photo of your current screen, and we will come back with a written quote.